Live centre point MK2
€20.50*
Prices incl. 19% VAT. plus Shipping costs
Delivery time: 1-3 working days **
More than 10 pieces available (online and in specialist shops)
Intended use
A centre point (often also referred to as a centring point or rolling centre) is one of the most important tools when working on a lathe. It is fitted into the tailstock as a securing device to enable even long, thin and heavy workpieces to be machined safely and with dimensional accuracy. Centre points are primarily used at higher speeds.
Technical data
| Base body material: | 100 Cr6 steel |
|---|---|
| Concentricity (max.) [mm]: | 0,007 |
| Material lace: | 100 Cr6 steel |
| Morse taper recording: | MK2 |
| Point angle [°]: | 60 |
| Speed (max.) [rpm]: | 1.500 |
| Total length [mm]: | 137 |
| Ø bearing housing [mm]: | 41 |
| Ø tip [mm]: | 17,5 |
One of the most important accessories for a lathe
For securing long, thin and heavy workpieces
Concentricity: max. 0.007 mm
Steel centre point, hardened and ground
Further sizes (MK0 – MK4) in our range
Description of the
The centre point has double bearings and therefore achieves a high concentricity of max. 0.007 mm. It can be used up to a speed of 1,500 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
Scope of delivery
- 1 x MK2 rotating centre point
More about the brand and products from
The centre point has double bearings and therefore achieves a high concentricity of max. 0.007 mm. It can be used up to a speed of 1,500 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
This adjustable fixed centre point is an accessory for lathes and is used for taper turning and cone turning. It enables lateral adjustment of the workpiece support without moving the lathe’s tailstock using the traditional method. This allows conical workpieces to be machined in a controlled manner with reduced setup effort. The centre point is fixed and does not rotate with the workpiece. It is used to support the workpiece between centres and is particularly suitable for applications where robust and simple support is required when turning conical shapes. The centre angle is 60°, making it suitable for typical centring tasks in turning operations. The centre point can be moved laterally by up to +/- 7 mm using the adjustment mechanism. This allows the desired taper or cone to be precisely set. The scale aids controlled adjustment and facilitates repeatable setting for suitable applications. With an overall length of 153 mm and a tip diameter of 24 mm, the centre point is designed for use on compatible lathes. The MK2 + MK3 version enables attachment to machines with a matching Morse taper mount. The adjustable fixed centre point is suitable for machining cones, tapered fits, adaptors, sleeves and similar workpiece shapes. It is a practical solution for users who wish to produce tapered workpieces on a lathe without having to reposition the tailstock themselves.
The centre point tip is mounted on a double bearing, thereby achieving a high concentricity of max. 0.007 mm. It can be used at speeds of up to 1,500 rpm. The steel tip is hardened and ground, increasing the load-bearing capacity and service life of this product. The tip angle of this centre point is – as is standard for centre points – 60°.
Unlike fixed centres, the tip of a live centre rotates with the workpiece, preventing friction and enabling higher speeds.
We supply rotating centring tips in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a high concentricity of max. 0.007 mm. It can be used up to a speed of 1500 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a high concentricity of max. 0.015 mm. It can be used up to a speed of 2,800 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a high concentricity of max. 0.015 mm. It can be used up to a speed of 2,800 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a high concentricity of max. 0.015 mm. It can be used up to a speed of 2,800 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a high concentricity of max. 0.015 mm. It can be used up to a speed of 2,800 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a very high concentricity of max. 0.003 mm. It can be used up to a speed of 8,000 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a very high concentricity of max. 0.003 mm. It can be used up to a speed of 8,000 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The centre point has double bearings and therefore achieves a very high concentricity of max. 0.003 mm. It can be used up to a speed of 6,000 rpm. The steel tip is hardened and ground, which increases the load capacity and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The steel tip is hardened and ground, which increases the resilience and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
The steel tip is hardened and ground, which increases the resilience and service life of this item. The point angle of this centre point is 60°, as is usual for centre points.
In contrast to fixed centre points, the tip of live centre points rotates with the workpiece, which prevents friction and enables higher speeds.
We supply live centre points in sizes MK0 to MK4.
€20.50*
Contents: 1 Piece
€52.00*
Contents: 1 Piece
€22.90*
Contents: 1 Piece
€31.90*
Contents: 1 Piece
€18.50*
Contents: 1 pcs
€22.00*
Contents: 1 pcs
€27.90*
Contents: 1 pcs
€16.90*
Contents: 1 pcs
€122.90*
Contents: 1 Piece
€117.90*
Contents: 1 Piece
€153.90*
Contents: 1 Piece
€12.00*
Contents: 1 pcs
€12.00*
Contents: 1 pcs
1 - 10 by 70 Reviews
27 July 2026 17:47
Läuft sehr präzise.
Bin sehr zufrieden. Die Spitze läuft sehr präzise und ist super verarbeitet.
12 May 2026 13:50
sehr gute Qualität, schnelle Lieferung
sehr gute Qualität, schnelle Lieferung
29 April 2026 08:03
Läuft bisher gut 👍
Läuft bisher gut 👍
27 February 2026 16:54
👍
👍
19 January 2026 18:42
Noch nicht gebraucht, vertraue auf gute Qualität.
Noch nicht gebraucht, vertraue auf gute Qualität. Schnell geliefert.
7 August 2025 15:29
Bin sehr zufrieden,Rundlauf OK.
Bin sehr zufrieden,Rundlauf OK.
21 February 2025 05:42
Empfehlenswert
Gute Qualität und guter Preis.
9 February 2025 19:14
Die Körnerspitze ist gut
Die Körnerspitze ist gut
13 January 2025 13:59
Looks good ... just what I ordered
Looks good ... just what I ordered
8 January 2025 08:45
Sehr gute Ware gerne wieder.
Sehr gute Ware gerne wieder.