Mounting flange for ER32 collets Ø 100 mm
€46.50*
Prices incl. 19% VAT. plus Shipping costs
Delivery time: 1-3 working days **
More than 10 pieces available (online and in specialist shops)
Intended use
With a mounting flange for collets, these can also be used on a lathe. In contrast to clamping with three-jaw or four-jaw chucks, clamping with collets ensures that the material is clamped cleanly and gently, and pressure marks are avoided, especially on softer workpieces. As a rule, collet systems have a higher concentricity compared to lathe chucks.
Technical data
| Concentricity deviation max. [mm]: | 0.025 (10 mm) / 0.04 (50 mm) |
|---|---|
| Cylindrical internal fit [mm]: | 72 |
| Diffuser [mm]: | 24 |
| Drill holes: | 3 x M8 |
| Max. revolutions [rpm].: | 1.400 |
| Outer diameter Ø [mm]: | 100 |
| Pitch circle [mm]: | 84 |
| Recording: | Cylindrical holder |
| Total height (incl. union nut) [mm]: | 50 |
| Material: | Steel, hardened and ground |
Made of steel, hardened and ground
For holding ER32 collets
For clean and gentle clamping, even of smaller diameters
Concentricity deviation max.: 0.025 mm with 10 mm overhung / 0.04 mm with 50 mm overhung
Description of the
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with a 100 mm cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
- Insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
- Screw the union nut with the inserted collet into the mounting flange.
Scope of delivery
- 1 x mounting flange for ER32 collets Ø 100 mm
- 1 x hook spanner for ER32
More about the brand and products from
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with a 100 mm cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
- Insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
- Screw the union nut with the inserted collet into the mounting flange.
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with a 125 mm cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
- Insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
- Screw the union nut with the inserted collet into the mounting flange.
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with a 160 mm holder with a cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
- Insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
- Screw the union nut with the inserted collet into the mounting flange.
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with a 200 mm cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
- 1. insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
- 2 Screw the union nut with the inserted collet chuck into the mounting flange.
This mounting flange for ER32 collets is made of hardened steel, the surfaces are ground. The flange can be mounted on lathes with an 80 mm cylindrical holder instead of a lathe chuck. The clearance is 24 mm.
Procedure for inserting ER collets:
1. insert the groove of the collet at an angle into the eccentric ring of the union nut until it audibly engages.
2 Screw the union nut with the inserted collet chuck into the mounting flange.
€46.50*
Content: 1 pcs
€47.00*
Content: 1 pcs
€73.50*
Content: 1 pcs
€123.50*
Content: 1 pcs
€46.00*
Content: 1 pcs
16 November 2023 19:07
Schnell und Gut wie immer!!!
Schnell und Gut wie immer!!!
9 September 2023 19:01
Guter Aufnahmeflansch
Die 72 mm Zentrierung hat ca. 0,05 mm Spiel zum Aufnahmeflansch der Drehmaschine, der Aufnahmeflansch muss also vor der Verwendung mittels Messuhr zentriert werden. Dafür einen Punkt Abzug. Allerdings lässt er sich dadurch mit ein wenig Aufwand 100-Prozentig ausrichten. Ich habe dann mit einem am zylindrischen Teil eingespannten MK2-Prüfdorn den Rundlauf in 100 mm Entfernung vom Futter überprüft: Es gibt keine Abweichung! Bin positiv überrascht.
10 March 2023 10:03
El producto está bien, PERO me gustaría
El producto está bien, PERO me gustaría que quedase más ajustado en la nariz del husillo... es decir, que quedase algo más apretado...
2 January 2023 15:22
Top kwaliteit!
Top kwaliteit!
2 January 2023 09:07
3
Die Anlagefläche des Flansch an die Drehmaschine ist nicht sauber ausgeschliffen. Ein Stück ist noch vom Härten schwarz geblieben. Es wird zwar gehen, aber ist ein Qualitätsmagel. Ich komme aus dem Wekzeugmaschinenbau. So was liefern wir nicht.Zum Rundlauf des Kegel kann ich noch nichts sagen.
26 October 2022 15:26
Gute Qualität, schnell geliefert.
Wie immer, günstig, gute Qualität, schnell geliefert.
19 September 2022 14:13
passt, Rundlauf ok
passt, Rundlauf ok
27 August 2022 06:49
Pas encore utilisé, mais le montage ce
Pas encore utilisé, mais le montage ce fait très bien sur tour SC4. Ne pas oublier les pinces! Le service Paulimot au top. Excellent
20 April 2022 18:01
Als Werkstückaufnahme zum drehen top. Holt aus
Als Werkstückaufnahme zum drehen top. Holt aus der Drehmaschine raus , was sie kann.
12 November 2021 00:00
Flansch
Läuft absolut rund.Spitze.