Skip to main content

Lathe SIEG C2, 250 watts, 400 mm centre distance

Bargain: Former exhibition piece, this machine was NOT used for machining, it was only used for demonstration purposes!

Intended use

This lathe is the version of the SIEG C2 with a centre distance of 400 mm (instead of 350 mm). The machine is used for turning rotationally symmetrical workpieces (e.g. cylindrical turned parts). The SIEG C2 bench lathe is suitable for "small chips" and is therefore intended for the production of smaller turned parts. It is suitable for machining softer materials such as plastic, aluminium, copper or zinc.

Technical data

Bed width [mm]: 83
Centre distance [mm]: 400
Centre height [mm]: 90
Circulation Ă˜ over cross slide [mm]: 110
Clamping range inner jaws [mm]: 2 - 90, 2 – 90
Clamping range outer jaws [mm]: 30 - 80, 30 – 80
Concentricity of lathe chuck [mm]: max. 0.040
Frequency [Hz]: 50
Gross weight [kg]: 51
Lathe chuck diameter [mm]: 100
Lead of top slide spindle [mm]: 1
Lead screw pitch [mm]: 1,5
Longitudinal feed [mm]: 0,1, 0,1 - 0,2
Machine dimensions (L x W x H) [mm]: 800 x 300 x 360
Max. torsion bar height [mm]: 8
Motor power P1 [W]: 370
Motor power P2 [W]: 250
Net weight [kg]: 38
Number of longitudinal feeds: 10
Number of thread pitches (metric): 10
Packaging dimensions (L x W x H) [mm]: 900 x 380 x 380
Pitch face slide spindle [mm]: 1
Quadruple steel holder Mounting height [mm]: 15
Rotation Ă˜ over machine bed [mm]: 180
Scale division on the cross slide handwheel [mm] / [in]: 0,025 / 0,001
Scale division on top slide handwheel [mm] / [in]: 0,025 / 0,001
Spindle bore [mm]: 20
Spindle cone: MK3
Spindle holder: Cylindrical according to DIN6350, cylindrical DIN 6350, cylindrical DIN6350
Spindle speed [rpm].: 100 - 2.500
Steps Spindle speed: variable
Tailstock cone: MK2
Tailstock quill stroke [mm]: 55
Thread pitch [mm]: 0,4 - 2,0, 0,4 – 2,0
Tool holder: 4-fold
Top slide rotatable [°]: 360 / Scale up to 45
Travelling distance of the cross slide [mm]: 70
Travel of the bed slide [mm]: 375
Travel of the top slide [mm]: 70
Voltage [V]: 230
WEEE reg. no.: EN 95902713

230 volt motor with 250 watts

100 mm three-jaw chuck (instead of 80 mm)

Reversible centre for cutting left-hand threads - Lead screw cover

400 mm centre distance (instead of 350 mm)

Low noise at all speeds

Description of the

The SIEG C2 is a 230 volt bench lathe with variable speed control. It is driven by a 250 watt brush motor. In order to achieve sufficient torque even at low speeds, the small lathe has a reduction gear. A lever on the back of the mini lathe can be used to select between the "fast" and "slow" speed ranges. The SIEG C2 is a lead screw lathe. It has a longitudinal feed for thread cutting. A reversible centre allows the direction of rotation of the lead screw to be changed independently of the direction of rotation of the lathe chuck. This means that left-hand threads can be produced with this lathe. The speed controller, the toggle switch for the direction of rotation of the main spindle and the emergency stop button are located on the control panel. Ten metric thread pitches from 0.4 to 2.0 millimetres can be achieved using the interchangeable plastic gears included in the scope of delivery.

Scope of delivery

  • 1 x operating instructions in German
  • 1 x set of change gears
  • 1 x set of hexagon socket spanners
  • 1 x set of open-end spanners
  • 1 x chuck spanner
  • 1 x fixed centre punch MK2
  • 1 x 3-jaw chuck0 100 mm with inner and outer jaws
  • 4 x rubber feet incl. fastening screws
  • 1 x oil tube

More about the brand and products from 

3 of 3 reviews

Average rating of 5 out of 5 stars


100%

0%

0%

0%

0%


Leave a review!

Share your experiences with other customers.

Excellent

Very good

Good

Acceptable

Unsatisfactory

This site is protected by reCAPTCHA and the Privacy Policy and Terms of Use apply.

30 April 2022 08:43

Review with rating of 5 out of 5 stars

Wie bestellt und bei Abholung alles war

Wie bestellt und bei Abholung alles war da.

27 July 2021 00:00

Review with rating of 5 out of 5 stars

Sieg C2

Schnelle und sichere Lieferung der Maschine. Die ersten Drehergebnisse lassen keinen Zweifel aufkommen, dass die Maschine jeden Euro wert ist. Die Lackschäden halten sich in Grenzen

4 July 2021 00:00

Review with rating of 5 out of 5 stars

Drehmaschine

Sehr präzise und einfach zu handhaben. Gutes Gerät.

Information on the manufacturer (information obligations under the GPSR Product Safety Regulation)
Paulitschek Maschinen- und Warenvertriebsgesellschaft mbH
ZeppelinstraĂŸe 3
89231 Neu-Ulm, Deutschland
+49 731 23232
support@paulimot.de